YAMAHA XVS650 CLASSIC/DRAGSTAR/CUSTOM 1997-2019 410MM SLASH CUT EXHAUST SYSTEM

All Delkevic complete systems come with gaskets (where needed) clamps. We manufacture all our exhaust components in our own factory employing the most stringent quality control procedures.

Fits

1997 Yamaha XVS650A DragStar Classic
1998 Yamaha XVS650A DragStar Classic
1999 Yamaha XVS650A DragStar Classic
2000 Yamaha XVS650A DragStar Classic
2001 Yamaha XVS650A DragStar Classic
2002 Yamaha XVS650A DragStar Classic
2003 Yamaha XVS650A DragStar Classic
2004 Yamaha XVS650A DragStar Classic
2005 Yamaha XVS650A DragStar Classic
2006 Yamaha XVS650A DragStar Classic
2007 Yamaha XVS650A DragStar Classic
2008 Yamaha XVS650A DragStar Classic
2009 Yamaha XVS650A DragStar Classic
2010 Yamaha XVS650A DragStar Classic
2011 Yamaha XVS650A DragStar Classic
2012 Yamaha XVS650A DragStar Classic
2013 Yamaha XVS650A DragStar Classic
2014 Yamaha XVS650A DragStar Classic
2015 Yamaha XVS650A DragStar Classic
2016 Yamaha XVS650A DragStar Classic
2017 Yamaha XVS650A DragStar Classic
2018 Yamaha XVS650A DragStar Classic
2019 Yamaha XVS650A DragStar Classic
1997 Yamaha XVS650 DragStar
1998 Yamaha XVS650 DragStar
1999 Yamaha XVS650 DragStar
2000 Yamaha XVS650 DragStar
2001 Yamaha XVS650 DragStar
2002 Yamaha XVS650 DragStar
2003 Yamaha XVS650 DragStar
2004 Yamaha XVS650 DragStar
2005 Yamaha XVS650 DragStar
2006 Yamaha XVS650 DragStar
2007 Yamaha XVS650 DragStar
2008 Yamaha XVS650 DragStar
2009 Yamaha XVS650 DragStar
2010 Yamaha XVS650 DragStar
2011 Yamaha XVS650 DragStar
2012 Yamaha XVS650 DragStar
2013 Yamaha XVS650 DragStar
2014 Yamaha XVS650 DragStar
2015 Yamaha XVS650 DragStar
2016 Yamaha XVS650 DragStar
2017 Yamaha XVS650 DragStar
2018 Yamaha XVS650 DragStar
2019 Yamaha XVS650 DragStar

Frequently Asked Questions

• What is the silencer made of?..
  The silencer outer sleave is made from 304 stainless steel skillfully welded and highly polished.
• How does it attach to the bike?..
  These silencer sleaves have two 8mm bolts on the inner side of the silencer that work with the supplied specific bracket for your model.
• What is the inlet I.D of the silencer?..
  Inlet I.D is 50.8mm and is a common size for most models.
• What is the diameter of the silencer?..
  The O.D of the silencer is 80mm.
• Can you adjust the angle of the exhaust tip to point down or out?..
  Yes, Our system has 5 different positions, You can adjust position by removing one 4mm allen key bolt and turning until you see another thread then re fit the bolt.
• How loud is this system?
  Loud when you open the throttle not so loud at idle or low RPMs.
• Does it have a removeable baffle?.
  Yes this comes with a baffle pre installed, You can remove if you want it to be louder.
• Do you have a quieter baffle for this silencer?.
  Not currently however the standard baffle it comes with does a pretty good job.
• Can you repack this silencer?..
  No these are not repackable silencers however replacement internal cartridges are available.
• What is this silencer made from?
  304 Stainless steel highly polished.
• How long do I allow the sealant to dry?
  We recommend you leave the sealant to cure for 24hrs before starting the bike.
• Where do I use the sealant?
  Use the sealant on every pipe to pipe join as this will help seal the system and prevent any exhaust gas leaks.

COM38BD